home *** CD-ROM | disk | FTP | other *** search
- ;--- Harvey's Robot v4.30 * Configuration / Mail List File
- ; by Harvey Parisien, FidoNet 1:249/114
-
- ; €€ ORIGIN... (one only)
- ;
- ; origin_zone:net/node{.point},name,origin line,outbound path,packet extension {,route_net,route_node}
- ;
- ; Note: Normally, your packet extension should follow this logic...
- ; If firing mail directly into Outbound directories, use OUT
- ; If firing mail directly into Inbound directories, use PKT
- ;
- ; ----------------------------------------------------------------------------
- 1:249/114.7, Harvey Parisien, OFFLINE Systems, \max\msg\outmail\, OUT
-
- ; €€ DESTINATIONS... (unlimited)
- ;
- ; All other lines are messages to be sent out. Each message line
- ; must contain...
- ;
- ; destination_zone:net/node{.point}, to, subject, ATTR, message.ext, AREAtag
- ;
- ; Note: ATTR can be set for Public, Private, File Attach, or File Request.
- ; All messages other than Public will be sent as Private.
- ;
- ; Set ATTR to...
- ;
- ; 0 for a Public Message
- ; P for a Private Message
- ; A for a file attachment (put full drive:\path\filename on subject line)
- ; R for a file request (put request on subject line)
- ;
- ; Note: If ATTR is A or R the message will be sent netmail only, echotags
- ; will be ignored if you were very sleepy and forgot...
- ; The areatag must be a legal tag name as it appears in your AREA
- ; control files. By NOT using an areatag, the message becomes NETMAIL.
- ;
- ; Note: MESSAGE.EXT is any text file which will become the message body.
- ; If MESSAGE.EXT is blank, the system will look for the marker ---
- ; after your destination addresses, and use everything below it for
- ; the message body. This is where having everything in one self
- ; contained file is prefered. Then follow with your origin line etc.
- ;
- ; Note: MESSAGE.EXT can be replaced with a variable &FILE where where the
- ; second command line parameter delimited with a , will be used in
- ; place of this variable for one or more destinations. If &FILE is
- ; not found, then the system will assume the message.ext is blank and
- ; revert to the --- message text mode if that was implemented. You
- ; might have a default message of say...
- ; ---
- ; Report not available
- ;
- ; Note: The first uncommented line is usually your origin description line.
- ; However, if you want to change the delimiter used in this file, which by
- ; default is a comma (,), you can do so by placing ONE charactor on the first
- ; uncommented line which will then become your delimiter for the balance of
- ; the Configuration / Mail List File.
- ;
- ; Note: Front Door users... since FD uses a different method of dealing with
- ; file attaches etc., the normal way of stripping pathing info on the subject
- ; line for a file attach can be disabled. Place the two characters FD on the
- ; first line of your Configuration / Mail List File. This should be even
- ; before the above mentioned delimiter change command if you use it. If you
- ; use the delimiter change command and the FD command, put the new delimiter
- ; on the line after the FD command.
-
- ; ----------------------------------------------------------------------------
- 1:249/114, All, BBS List Update, 0, BBSLIST.TXT, USERS249
- 1:249/1, Bill Cassidy, Private Stuff..., P, MESSAGE.TXT,
- 1:249/106, Scott Dudley, FILES, R, FREQ.TXT,
- 1:249/124,Don Laverdure,FSEARCH.ZIP,R,FREQ.TXT,
- 1:249/2,Ian Silver,c:\max\file\hp\HARVEY42.ZIP,A,ATTACH.TXT,
- 2:254/71,Cliff Jones,Stuff...,P,message.txt,
-